Skip to main content

Sky Wave, Microwave Link Communication and Satellite Communication (SATCOM)


Overview

Sky Wave, Microwave Link Communication, and Satellite Communication  (SATCOM) are the focus of this article. Sky Waves are essentially AM waves that the ionosphere reflects. For long-distance communication on Earth, we employ standard microwave link transmission. However, we all know that the earth is not flat, but rather oval in shape. As a result, the signal can only reach a few kilometers on a straight line of sight path (LOS). The signal is then reflected by the earth's surface. But we know that with that microwave link, we can communicate hundreds of kilometers distance. We'll look at how this happens in this article. Terrestrial satellite communication has now replaced microwave relay link communication.

sky wave

Figure: Ionosphere Reflection - suitable for AM band (Sky Wave)

1. Sky Wave

You can see how the ionosphere bounces the radio signal and enables the ground station to communicate with the transmitter hundreds of kilometers away. This method is ideal for communication at low or medium frequencies. Ionosphere reflects low (AM band) or medium (<30 MHz) range frequency.

Due to its high frequency, the microwave band cuts through the ionosphere, making it ideal for communicating with satellites. However, with the help of the ionosphere, we can efficiently receive a signal at a distance of roughly 650 kilometers from the transmitter.


1.1. Role of Ionosphere for Sky Wave

The ionosphere is one of the top levels of the earth's atmosphere, as we all know. Its altitude ranges from 30 to 600 miles above the earth's surface. We, as humans, reside in the troposphere. Atoms and molecules in the ionosphere are electrically charged. The ionosphere has the unique property of reflecting radio signals below 30 MHz. Signals with operating frequencies greater than 30 MHz penetrate the ionosphere layer. Also, do not return to Earth. In this situation, we always keep the frequency below 30 MHz. When we send a signal via a microwave link, the earth's ionosphere reflects it. In the diagram above, the transmitter emits a signal, which is then reflected by the ground and, in a similar way, by the ionosphere. According to our knowledge, a received signal reflected by the ionosphere is easier to receive by a receiver than a reflected signal by the ground.   

1.3. Frequency Range

535 to 1705 KHz


2. Microwave Link Communication

For terrestrial microwave communication, we depended largely on relay communication. For line-of-sight communication, each relay station is situated 150-200 kilometers apart. However, a key disadvantage of relay communication was that if one of the relay stations in the middle failed, the entire system would fail. As a result, we rely more on satellites. Microwave, on the other hand, is significantly more refracted by hills than low-frequency AM band. As a result, the considerable path loss is observed in the case of microwaves when employing a microwave relay link. In the case of microwave communication, the line of communication is also taken into account.  
microwave link communication

 
 
Microwave link communication is used for long-distance microwave communication. In this situation, a powerful directional microwave beam is used to go further in the earth's troposphere. 

2.1. Frequency Range:

Although microwave frequencies can range from 300 MHz to 300 GHz, we often choose sub-6 GHz frequencies or frequencies between 1 and 6 GHz for microwave link communication.

.

3. Satellite Communication

However, you should be aware that a line-of-sight connection between the transmitter and the receiver is not possible during the whole communication path. Before that signal is reflected by the ground, foliage, and other objects, it becomes scattered and weaker. On the other hand, if one intermediary relay fails, the entire communication system will stop working. As a result, we rely on the signal reflected by the satellites in this case. If there is no ionosphere or satellite, the signal can only travel 150 - 200 kilometers (approx.) as shown in the above figure. Satellite television is a real-world example of terrestrial satellite communication.

3.1. Frequency Range:

Frequencies range from 1 to 40 GHz.
satellite communication

Difference between advantages of tropospheric wave propagation and sky wave (waves reflected or refracted by ionosphere) propagation



People are good at skipping over material they already know!

View Related Topics to







Contact Us

Name

Email *

Message *

Popular Posts

BER vs SNR for M-ary QAM, M-ary PSK, QPSK, BPSK, ...(MATLAB Code + Simulator)

Bit Error Rate (BER) & SNR Guide Analyze communication system performance with our interactive simulators and MATLAB tools. 📘 Theory 🧮 Simulators 💻 MATLAB Code 📚 Resources BER Definition SNR Formula BER Calculator MATLAB Comparison 📂 Explore M-ary QAM, PSK, and QPSK Topics ▼ 🧮 Constellation Simulator: M-ary QAM 🧮 Constellation Simulator: M-ary PSK 🧮 BER calculation for ASK, FSK, and PSK 🧮 Approaches to BER vs SNR What is Bit Error Rate (BER)? The BER indicates how many corrupted bits are received compared to the total number of bits sent. It is the primary figure of merit for a...

Online Simulator for ASK, FSK, and PSK

Try our new Digital Signal Processing Simulator!   •   Interactive ASK, FSK, and BPSK tools updated for 2025. Start Now Interactive Modulation Simulators Visualize binary modulation techniques (ASK, FSK, BPSK) in real-time with adjustable carrier and sampling parameters. 📡 ASK Simulator 📶 FSK Simulator 🎚️ BPSK Simulator 📚 More Topics ASK Modulator FSK Modulator BPSK Modulator More Topics Simulator for Binary ASK Modulation Digital Message Bits Carrier Freq (Hz) Sampling Rate (...

ASK, FSK, and PSK (with MATLAB + Online Simulator)

📘 ASK Theory 📘 FSK Theory 📘 PSK Theory 📊 Comparison 🧮 MATLAB Codes 🎮 Simulator ASK or OFF ON Keying ASK is a simple (less complex) Digital Modulation Scheme where we vary the modulation signal's amplitude or voltage by the message signal's amplitude or voltage. We select two levels (two different voltage levels) for transmitting modulated message signals. Example: "+5 Volt" (upper level) and "0 Volt" (lower level). To transmit binary bit "1", the transmitter sends "+5 Volts", and for bit "0", it sends no power. The receiver uses filters to detect whether a binary "1" or "0" was transmitted. Fig 1: Output of ASK, FSK, and PSK modulation using MATLAB for a data stream "1 1 0 0 1 0 1 0" ( Get MATLAB Code ) ...

Constellation Diagrams of ASK, PSK, and FSK (with MATLAB Code + Simulator)

Constellation Diagrams: ASK, FSK, and PSK Comprehensive guide to signal space representation, including interactive simulators and MATLAB implementations. 📘 Overview 🧮 Simulator ⚖️ Theory 📚 Resources Definitions Constellation Tool Key Points MATLAB Code 📂 Other Topics: M-ary PSK & QAM Diagrams ▼ 🧮 Simulator for M-ary PSK Constellation 🧮 Simulator for M-ary QAM Constellation BASK (Binary ASK) Modulation Transmits one of two signals: 0 or -√Eb, where Eb​ is the energy per bit. These signals represent binary 0 and 1. BFSK (Binary FSK) Modulation Transmits one ...

Theoretical BER vs SNR for m-ary PSK and QAM

Relationship Between Bit Error Rate (BER) and Signal-to-Noise Ratio (SNR) The relationship between Bit Error Rate (BER) and Signal-to-Noise Ratio (SNR) is a fundamental concept in digital communication systems. Here’s a detailed explanation: BER (Bit Error Rate): The ratio of the number of bits incorrectly received to the total number of bits transmitted. It measures the quality of the communication link. SNR (Signal-to-Noise Ratio): The ratio of the signal power to the noise power, indicating how much the signal is corrupted by noise. Relationship The BER typically decreases as the SNR increases. This relationship helps evaluate the performance of various modulation schemes. BPSK (Binary Phase Shift Keying) Simple and robust. BER in AWGN channel: BER = 0.5 × erfc(√SNR) Performs well at low SNR. QPSK (Quadrature...

FIR vs IIR Digital Filters and Recursive vs Non Recursive Filters

Filters >> FIR vs. IIR Digital Filters and Recursive vs. Non-Recursive Filters Key Features The higher the order of a filter, the sharper the stopband transition The sharpness of FIR and IIR filters is very different for the same order A FIR filter has an equal time delay at all frequencies, while the IIR filter's time delay varies with frequency. Usually, the biggest time delay in the IIR filter is at the filter's cutoff frequency. The term 'IR' (impulse response) is in both FIR and IIR. The term 'impulse response' refers to the appearance of the filter in the time domain. 1. What Is the Difference Between an FIR and an IIR Filters? The two major classifications of digital filters used for signal filtration are FIR and IIR....

Comparisons among ASK, PSK, and FSK (with MATLAB + Simulator)

📘 Comparisons among ASK, FSK, and PSK 🧮 Online Simulator for calculating Bandwidth of ASK, FSK, and PSK 🧮 MATLAB Code for BER vs. SNR Analysis of ASK, FSK, and PSK 📚 Further Reading 📂 View Other Topics on Comparisons among ASK, PSK, and FSK ... 🧮 Comparisons of Noise Sensitivity, Bandwidth, Complexity, etc. 🧮 MATLAB Code for Constellation Diagrams of ASK, FSK, and PSK 🧮 Online Simulator for ASK, FSK, and PSK Generation 🧮 Online Simulator for ASK, FSK, and PSK Constellation 🧮 Some Questions and Answers Modulation ASK, FSK & PSK Constellation MATLAB Simulink MATLAB Code Comparisons among ASK, PSK, and FSK    Comparisons among ASK, PSK, and FSK Comparison among ASK, FSK, and PSK Parameters ASK FSK PSK Variable Characteristics Amplitude Frequency ...