Skip to main content

Best Wireless Communication Based Projects for Final Year Students



Our colleges either give us projects individually or require us to work in groups to complete them. You want to be able to apply theoretical concepts to real-world situations when working on a project. You will gain a greater understanding of a subject by applying your theoretical knowledge to a project, and you will face new challenges at work. And a researcher, engineer, or scientist's primary goal is to solve issues or difficulties in order to provide us with a better tomorrow. Excellence in a project, on the other side, can attract companies or investors. This will help you advance in your career.

We'll talk about various project/thesis ideas based on modern wireless communication. Both professors and students will benefit from it. Wireless communication is now being used in our everyday lives. Without a doubt, no other application in our lives is as dominant as electronics/wireless appliances.

Without further ado, we'll go through several project ideas that can be beneficial to B.E, B.Tech, or M.Tech students.


1. Comparison of ASK, FSK & PSK

(We know all modulation schemes are derived from these three primary modulation schemes i.e., ASK, FSK, & PSK) because in modulation we vary the amplitude, frequency or phase of carrier signal in accordance with amplitude of message signal. For example, QAM modulation scheme a combination of ASK & PSK)

Resources:

[1.1] ASK FSK PSK with simulation in MATLAB

[1.2] M-ary Modulation | QPSK & QAM | Constellation



2. M-ary Modulation (QPSK & QAM)

(M-ary modulation scheme is very important to increase the data rate of a system. Because here we send multiple bits as a symbol at a time unlike ASK, FSK & PSK. If we use 4 QPSK then we are able to send 4 bits at a time or data rate increases by four times rather than transferring one bit at a time)

[2.1] M-ary Modulation Techniques



3. Comparison of m-ary QPSK & QAM (especially when we increasing the number of bits in a symbol)

[3.1] BER vs SNR for QAM, QPSK ...

[3.2] MATLAB code for BER vs SNR for M-QAM & M-PSK



4. Terrestrial microwave communication

[4.1] Microwave Link Communication for Long-distance



5. Multi carrier modulation - OFDM
6. OFDM SC at uplink
7. UWB
8. Device ranging in UWB
9. UWB in WiFi 4 and above
10. Millimeter wave communication
11. 60 GHz Communication (57 - 64 GHz)
12. Short range high speed wireless communication
13. FHSS
15. Blutooth communication
16. Zigbee communication
17. Under-water wireless communication
18. SDM in MIMO
19. Spatial Multiplexing (SM) in MIMO
20. IPv6
21. Internet of things (IoTs)
22. Night Vision
23. Cybersecurity (using cryptography)
24. Technology: 4G vs. 5G
25. Fading in wireless communication channel
26. RFID
27. V2V communication
28. Smart city
29. IEEE 802.11
30. Software defined radio (SDR)
31. Laser based wireless communication




Also Read
[1] More Wireless Communication Based Projects for M.Tech


<<Previous Page
Next Page>>

# digital communication project using ask  #wireless communication based projects  #wireless communication projects for final year  #wireless communication projects using python  #wireless communication mini projects  #project on wireless communication
📊 MATLAB & ONLINE SIMULATIONS (Web-Based)
🎓 GATE & UGC - NET SOLUTIONS
📡 WIRELESS & SIGNAL PROCESSING


Contact Us

Name

Email *

Message *

Popular Posts

MATLAB Code for BER performance of QPSK with BPSK, 4-QAM, 16-QAM, 64-QAM, 256-QAM, etc

📘 Overview 🧮 MATLAB Codes 🧮 Online Simulator for Calculating BER of M-ary PSK and QAM 🧮 QPSK vs BPSK and QAM: A Comparison of Modulation Schemes in Wireless Communication 🧮 Are QPSK and 4-PSK same? 📚 Further Reading   QPSK offers double the data rate of BPSK while maintaining a similar bit error rate at low SNR when Gray coding is used. It shares spectral efficiency with 4-QAM and can outperform 4-QAM or 16-QAM in very noisy channels. QPSK is widely used in practical wireless systems, often alongside QAM in adaptive modulation schemes [Read more...] What is the Gray Code? Gray Code: Gray code is a binary numeral system where two successive values differ in only one bit. This property is called the single-bit difference or unit distance code. It is also known as reflected binary code. Let's convert binary 111 to Gray code: Binary bits: B = 1 1 1 Apply the rule: G[0] = B[0] = 1...
Read more

FFT Butterfly Method Explained (with Simulations)

4-Point FFT Using Butterfly Method Given: x[n] = {0, 1, 2, 3} Step 1: Split into Even & Odd Even indices: x e = {x[0], x[2]} = {0, 2} Odd indices: x o = {x[1], x[3]} = {1, 3} Step 2: 2-point DFT For any {a, b}: DFT = {a + b, a - b} Even Part (E): {0+2, 0-2} = {2, -2} Odd Part (O): {1+3, 1-3} = {4, -2} Step 3: Combine Using Butterfly X[k] = E[k] + W 4 k O[k] X[k + 2] = E[k] - W 4 k O[k] Twiddle Factors (N=4): W 4 0 = 1, W 4 1 = -j Final Calculations: X[0] = E[0] + W 4 0 O[0] = 2 + (1)(4) = 6 X[2] = E[0] - W 4 0 O[0] = 2 - (1)(4) = -2 X[1] = E[1] + W 4 1 O[1] = -2 + (-j)(-2) = -2 + 2j X[3] = E[1] - W 4 1 O[1] = -2 - (-j)(-2) = -2 - 2j Final Answer: X[k] = {6, -2 + 2j, -2, -2 - 2j} 8-Point FFT Using Butterfly Method Given: x[n] = {0,1,2,3,4,5,6,7} Step 1: Split into Bit-Reversed Order To perform DIT-FFT, split the 8 points into pairs of two: Group A: {x[0], x[4]} = {0, 4}...
Read more

MATLAB Code for QPSK Modulation and Demodulation

📘 Overview 🧮 MATLAB Codes 🧮 Theory 🧮 BER performance of QPSK with BPSK, 4-QAM, 16-QAM, 64-QAM, 256-QAM, etc 📚 Further Reading QPSK Passband Signal Generation Spectral Efficiency in QPSK   Quadrature Phase Shift Keying (QPSK) is a digital modulation scheme that conveys two bits per symbol by changing the phase of the carrier signal. Each pair of bits is mapped to one of four possible phase shifts: 0°, 90°, 180°, or 270° 00  ===> 0 degree phase shift of carrier signal 01  ===> 90 degree 11  ===> 180 degree 10  ===> 270 degree   MATLAB Script clc; clear all; close all; clc; M = 4; data = randi([0 (M-1)], 1000, 1); Phase = 0; modData=pskmod(data,M,Phase); figure(1); scatterplot(modData); channelAWGN = 15; rxData2 = awgn(modData, channelAWGN); figure(2); scatterplot(rxData2); demodData = pskdemod(rxData2,M,Phase);   Result data 1 0 2 2 0 2 1 . . . modData -1.0...
Read more

UGC NET Electronic Science Previous Year Question Papers with Solutions

Home / Engineering & Other Exams / UGC NET 2026 PYQ ⬇️ Download Papers and Solutions 📋 Exam Pattern 💡 Preparation Tips ❓ FAQs 📊 Exam Highlights: Electronic Science (88) Feature Details Junior Research Fellowship (JRF) ₹37,000 + HRA per month Eligibility M.Sc/M.Tech in Electronics (55%) Validity of Certificate JRF (3 Years) | Lectureship (Lifetime) 📥 Download UGC NET Electronics PDFs Complete collection of previous year question papers, answer keys and explanations for Subject Code 88. Start Downloading 📂 View All Question Papers June 2025 - Question Paper Download PDF June 2025 - Solved Paper + Explanation ...
Read more

Online Simulator for ASK, FSK, and PSK Signal Generation

Interactive Digital Signal Processing (DSP) Tutorial and Simulator for ASK, FSK, and BPSK modulation techniques. Try our new Digital Signal Processing Simulator!   •   Interactive ASK, FSK, and BPSK tools updated for 2025. Start Now Digital Modulation Visualizer: ASK, FSK, & BPSK Simulator Learn and visualize binary modulation techniques (ASK, FSK, BPSK) in real-time with adjustable carrier and sampling parameters. Perfect for DSP students and engineers. 📡 ASK Simulator 📶 FSK Simulator 🎚️ BPSK Simulator 📚 More Topics ASK Modulator FSK Modulator BPSK Modulator More Topics 1. ASK (Amplitude Shift Keying) Simulat...
Read more

OFDM Symbols and Subcarriers Explained

This article explains how OFDM (Orthogonal Frequency Division Multiplexing) symbols and subcarriers work. It covers modulation, mapping symbols to subcarriers, subcarrier frequency spacing, IFFT synthesis, cyclic prefix, and transmission. Step 1: Modulation First, modulate the input bitstream. For example, with 16-QAM , each group of 4 bits maps to one QAM symbol. Suppose we generate a sequence of QAM symbols: s0, s1, s2, s3, s4, s5, …, s63 Step 2: Mapping Symbols to Subcarriers Assume N sub = 8 subcarriers. Each OFDM symbol in the frequency domain contains 8 QAM symbols (one per subcarrier): Mapping (example) OFDM symbol 1 → s0, s1, s2, s3, s4, s5, s6, s7 OFDM symbol 2 → s8, s9, s10, s11, s12, s13, s14, s15 … OFDM sym...
Read more

BER vs SNR for M-ary QAM, M-ary PSK, QPSK, BPSK, ...(MATLAB Code + Simulator)

Bit Error Rate (BER) & SNR Guide Analyze communication system performance with our interactive simulators and MATLAB tools. 📘 Theory 🧮 Simulators 💻 MATLAB Code 📚 Resources BER Definition SNR Formula BER Calculator MATLAB Comparison 📂 Explore M-ary QAM, PSK, and QPSK Topics ▼ 🧮 Constellation Simulator: M-ary QAM 🧮 Constellation Simulator: M-ary PSK 🧮 BER calculation for ASK, FSK, and PSK 🧮 Approaches to BER vs SNR Calculation What is Bit Error Rate (BER)? The BER indicates how many corrupted bits are received compared to the total number of bits sent. It is the primary figur...
Read more

DFTs-OFDM vs OFDM: Why DFT-Spread OFDM Reduces PAPR Effectively (with MATLAB Code)

Understanding PAPR in DFT-spread OFDM vs. Standard OFDM In modern wireless communications like 4G LTE and 5G NR, managing the Peak-to-Average Power Ratio (PAPR) is critical for hardware efficiency. While OFDM is the gold standard for high-speed data, its high PAPR poses significant challenges for mobile devices. This is where DFTs-OFDM (also known as SC-FDMA) comes in. DFT-spread OFDM (DFTs-OFDM) has lower Peak-to-Average Power Ratio (PAPR) because it "spreads" the data in the frequency domain before applying IFFT, making the time-domain signal behave more like a single-carrier signal rather than a multi-carrier one like OFDM. Deeper Explanation: Aspect OFDM DFTs-OFDM Signal Type Multi-carrier Single-carrier-like Process IFFT of QAM directly QAM → DFT → IFFT PAPR Level High (due to many...
Read more